/usr/share/automake-1.9/am/subdirs.am is in automake1.9 1.9.6+nogfdl-4ubuntu1.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 | ## automake - create Makefile.in from Makefile.am
## Copyright (C) 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2003, 2005
## Free Software Foundation, Inc.
## This program is free software; you can redistribute it and/or modify
## it under the terms of the GNU General Public License as published by
## the Free Software Foundation; either version 2, or (at your option)
## any later version.
## This program is distributed in the hope that it will be useful,
## but WITHOUT ANY WARRANTY; without even the implied warranty of
## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
## GNU General Public License for more details.
## You should have received a copy of the GNU General Public License
## along with this program; if not, write to the Free Software
## Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
## 02110-1301, USA.
RECURSIVE_TARGETS += \
all-recursive check-recursive installcheck-recursive
.PHONY: $(RECURSIVE_TARGETS)
# This directory's subdirectories are mostly independent; you can cd
# into them and run `make' without going through this Makefile.
# To change the values of `make' variables: instead of editing Makefiles,
# (1) if the variable is set in `config.status', edit `config.status'
# (which will cause the Makefiles to be regenerated when you run `make');
# (2) otherwise, pass the desired values on the `make' command line.
$(RECURSIVE_TARGETS):
## Using $failcom allows "-k" to keep its natural meaning when running a
## recursive rule.
@failcom='exit 1'; \
for f in x $$MAKEFLAGS; do \
case $$f in \
*=* | --[!k]*);; \
*k*) failcom='fail=yes';; \
esac; \
done; \
dot_seen=no; \
target=`echo $@ | sed s/-recursive//`; \
list='$(SUBDIRS)'; for subdir in $$list; do \
echo "Making $$target in $$subdir"; \
if test "$$subdir" = "."; then \
dot_seen=yes; \
local_target="$$target-am"; \
else \
local_target="$$target"; \
fi; \
(cd $$subdir && $(MAKE) $(AM_MAKEFLAGS) $$local_target) \
|| eval $$failcom; \
done; \
if test "$$dot_seen" = "no"; then \
$(MAKE) $(AM_MAKEFLAGS) "$$target-am" || exit 1; \
fi; test -z "$$fail"
mostlyclean: mostlyclean-recursive
clean: clean-recursive
distclean: distclean-recursive
maintainer-clean: maintainer-clean-recursive
.PHONY: mostlyclean-recursive clean-recursive distclean-recursive \
maintainer-clean-recursive
## We run all `clean' targets in reverse order. Why? It's an attempt
## to alleviate a problem that can happen when dependencies are
## enabled. In this case, the .P file in one directory can depend on
## some automatically generated header in an earlier directory. Since
## the dependencies are required before any target is examined, make
## bombs.
mostlyclean-recursive clean-recursive distclean-recursive \
maintainer-clean-recursive:
## Using $failcom allows "-k" to keep its natural meaning when running a
## recursive rule.
@failcom='exit 1'; \
for f in x $$MAKEFLAGS; do \
case $$f in \
*=* | --[!k]*);; \
*k*) failcom='fail=yes';; \
esac; \
done; \
dot_seen=no; \
## For distclean and maintainer-clean we make sure to use the full
## list of subdirectories. We do this so that `configure; make
## distclean' really is a no-op, even if SUBDIRS is conditional. For
## other clean targets this doesn't matter.
case "$@" in \
distclean-* | maintainer-clean-*) list='$(DIST_SUBDIRS)' ;; \
*) list='$(SUBDIRS)' ;; \
esac; \
rev=''; for subdir in $$list; do \
if test "$$subdir" = "."; then :; else \
rev="$$subdir $$rev"; \
fi; \
done; \
## Always do `.' last.
rev="$$rev ."; \
target=`echo $@ | sed s/-recursive//`; \
for subdir in $$rev; do \
echo "Making $$target in $$subdir"; \
if test "$$subdir" = "."; then \
local_target="$$target-am"; \
else \
local_target="$$target"; \
fi; \
(cd $$subdir && $(MAKE) $(AM_MAKEFLAGS) $$local_target) \
|| eval $$failcom; \
done && test -z "$$fail"
|